Post by sand35x on Jan 13, 2013 8:41:28 GMT -6
square tube style slider drive shaft from hanson motorsports $450 with turbo 350 bolt in yoke.
2- 7.0 x 14.5 trailer house tires mounted on 5x4.5 trailer rims. one has bent rim and both are a little scuffed up but not bad, 10 ply. $50 for the pair.
floor mounted throttle with wire cable, looks just like a gard throttle, brand new $125
box and bubble coil springs-$10 a set
3 sets box a arms and spindles.they are straight and ball joints are good.$50 a set
fresh box front clip, has little rust on driver side bottom where it bolts on firewall. $50
fresh and clean 80's vic steel front bumper.$80 obo
pre ran 80's ford front bumper that is seam welded and still straight.
$60
pre ran 75 newport hood thats still straight. $20
3- box ford steel hoods $20 a piece
1- box lincoln steel hood $20
turbo 350 that needs a rebuild, i believe its a short tailshaft but i will have to check.$50
1994 bubble vic p72, pitched 5 inches at the box, preran 74 impala thats been seam welded and hardnosed to front, bubble steel rear bumper welded on rear, front suspension changed out to box a arms and spindles, body is totally gutted out. body and front clip are just sitting on frame(not bolted down), i can include bolts to bolt it down., the only rust on frame is the way inside of crush box thats closest to motor but i already plated it. $550
1998 crown vic p71, no motor trans or hood, drivers rocker is a little rusty and there is a quarter sized rust spot on passenger crush box(easily fixable) tires on it are not going with, i will have stock fords on it for a roller$400
pre ran 74 impala thats seam welded and a little plating, tweaked a little bit but still runnable. $50
xxx dash mounted brake pedal with extended pedal $100
home made steel fuel cell, only ran i two demos, come with filler on top and drain on bottom,$80
more will be added in acouple of days when i get to go through stuff.located at albany,mn 56307
(320) 293 2209
2- 7.0 x 14.5 trailer house tires mounted on 5x4.5 trailer rims. one has bent rim and both are a little scuffed up but not bad, 10 ply. $50 for the pair.
floor mounted throttle with wire cable, looks just like a gard throttle, brand new $125
box and bubble coil springs-$10 a set
3 sets box a arms and spindles.they are straight and ball joints are good.$50 a set
fresh box front clip, has little rust on driver side bottom where it bolts on firewall. $50
fresh and clean 80's vic steel front bumper.$80 obo
pre ran 80's ford front bumper that is seam welded and still straight.
$60
pre ran 75 newport hood thats still straight. $20
3- box ford steel hoods $20 a piece
1- box lincoln steel hood $20
turbo 350 that needs a rebuild, i believe its a short tailshaft but i will have to check.$50
1994 bubble vic p72, pitched 5 inches at the box, preran 74 impala thats been seam welded and hardnosed to front, bubble steel rear bumper welded on rear, front suspension changed out to box a arms and spindles, body is totally gutted out. body and front clip are just sitting on frame(not bolted down), i can include bolts to bolt it down., the only rust on frame is the way inside of crush box thats closest to motor but i already plated it. $550
1998 crown vic p71, no motor trans or hood, drivers rocker is a little rusty and there is a quarter sized rust spot on passenger crush box(easily fixable) tires on it are not going with, i will have stock fords on it for a roller$400
pre ran 74 impala thats seam welded and a little plating, tweaked a little bit but still runnable. $50
xxx dash mounted brake pedal with extended pedal $100
home made steel fuel cell, only ran i two demos, come with filler on top and drain on bottom,$80
more will be added in acouple of days when i get to go through stuff.located at albany,mn 56307
(320) 293 2209